rangerovers.pub
The only place for a coil spring is up Zebedee's arse
  1. Forum
  2. Range Rover P38
  3. Electrickery
  4. 7" Remote Screen - single Din Android Head Unit.
7" Remote Screen - single Din Android Head Unit.

Smiler

Member
Joined:
Posts: 426
#1

Now that title is a bit of a mouthful!

Anyway, I have just ordered one of these:
Joying 7"

It has GPS Sat Nav, MP3, MP4, Radio (DAB with an additional adapter), can be connected to front and rear cameras (available separately), steering wheel control programmable, can be connected to a USB hard drive full of your own music and video libraries and can drive two additional screens such as head rest screens for the kids.

What's more, it is branded. Most of you will probably associate something labeled as Joying 7" as something from an Anne Summers collection but they are a real firm and they do answer emails the same day.

The big draw to this one is that the screen is separate from the 'workings' and so can hopefully be installed where the oddments tray currently sits with no worries over depth.

I also intend to raise the HEVAC control unit up a slot to make it more accessible and have bought a single din oddments tray to sit below it.

I shall keep you updated as to its arrival and how I get on installing it all.

Regards,

Smiler.

Mukiwa

Member
Joined:
Posts: 244
#2

I look forwards to this as this is on my "to do" list

Smiler

Member
Joined:
Posts: 426
#3

It arrived first thing monday morning (a couple of days early) just before we set off on holiday. Very well packaged. I have taken photos and will upload when I get chance.
Having since got home I have attacked and can confirm that the 'head unit' box will fit down in the depths behind the HEVAC unit leaving the original stereo space clear for a cubby hole/odments tray which I have already purchased. I can also confirm that I have working steering whel controls.
Instructions are a bit lacking but then a lot of it will depend on variances between different vehicles. I am noting everything that I do to make it work in a P38 and will write it all up.
So far so good.

Morat

Member
Joined:
Posts: 2426
#4

That sounds ideal. Can you install Spotify?

Smiler

Member
Joined:
Posts: 426
#5

When I finally get it all up and running I'll let you know.

Smiler

Member
Joined:
Posts: 426
#6

Well here goes, the initial install post.

First, how it arrives:

enter image description here

enter image description here

enter image description here

enter image description here

enter image description here

enter image description here

enter image description here

enter image description here

enter image description here

Smiler

Member
Joined:
Posts: 426
#7

Installing the head unit.

enter image description here

The rear location bracket for the original radio.
enter image description here

Folded back out of the way, it can now be used to keep cables tucked tidily away.
enter image description here

Front face of head unit showing screen mounting clips and connection ribbon lead.
enter image description here

Plastic surround removed to give more space but mounting clips retained to protect ribbon cable from crushing.
enter image description here

Rear showing lots of connection options.
enter image description here

Lowered into position, front facing the driver, bottom face toward the heater box.
enter image description here

Smiler

Member
Joined:
Posts: 426
#8

Wiring

The unit comes with a choice of two looms, one of which is largely pre-terminated with a standard plug.
There are a number of 'free' wires that still need to be wired to suit your application.
There are two wires available for steering wheel controls.
The P38 only uses one wire for steering wheel inputs so only one requires connecting.

enter image description here

I discovered this after fitting pins to both wires...
enter image description here

enter image description here

https://scontent-lht6-1.xx.fbcdn.net/v/t1.0-9/39208443_10156611292398501_6062409946769653760_n.jpg?_nc_cat=0&oh=135c740771ae7d1b8f90fe44cd89e1d0&oe=5BC5DA58

All plugged in.
enter image description here

Also connected is the GPS aerial, radio aerial, reversing camera (not included) and the microphone (for hands free).
The two trailing USB cables have been routed to accessible locations, one in the redundant ash tray for USB memory stick access, the other will have a broadband dongle plugged into it.

Smiler

Member
Joined:
Posts: 426
#9

Fitting the screen - Part 1

enter image description here

Remove front strip from cubby hole area (metal locking star washers on plastic studs on rear face).
enter image description here

The cubby hole wil need to be cut off.
enter image description here

Cut back from the edge.
enter image description here

Then file any edges down level with surrounding structure.
enter image description here

Trial fitting the screen, it needs to sit tight to the bottom edge and against the clock mount.
Note the original mounting clips for attaching to the head unit.
enter image description here

Lower edge also needs removing.
enter image description here

enter image description here

Once happy the edges can be tidied up with files and abrasive paper.
enter image description here

Smiler

Member
Joined:
Posts: 426
#10

Fitting the screen - Part 2

enter image description here

Two strips of U-section metal are required. In this case I have cut down some alloy box section down to suite.
enter image description here

The 'walls' need triming down each end. only by 1mm at one end and enough to allow it to be slid into position at the other.
enter image description here

Corrosponding slots are then cut into the switch mounting structure and the top of the oiginal head unit cut-out.
enter image description here

Use the screen to get the positioning dorrect. Don't forget to make sure that it is tight to the bottom edge and the clock mount.
enter image description here

enter image description here

The thinner 'tang' goes to the top.
enter image description here

The ends need to be filed flush to the surrounding structure.
enter image description here

enter image description here

Remove the four mounting clips from the back of the screen and with the screen hard against the bottom right edge and the two strips pushe up hard against the switch mounts, drill two screw holes on each strap to line up with the existing screw holes in the back of the screen.
enter image description here

The screen should now be secure in place.
enter image description here

Smiler

Member
Joined:
Posts: 426
#11

Fitting.

enter image description here

The screen will interfere with some of the original support structure so this needs to be cut away. Thankfully, being a Land Rover product as opposed to a flimsy french thing there is enough inherent strength and rigidity in it all to take it.
enter image description here

Screen ribbon plugged in.
enter image description here

All done. Note that there is enough space to alow fitment of a single din sized oddments tray in the now vacant head unit slot.
enter image description here

More to follow...

no10chris

Member
Joined:
Posts: 1327
#12

Looks good, let us know what you think of the unit.

GeorgeB

Member
Joined:
Posts: 487
#13

Like that.

Really must do something about the non-existent ICE in mine one day.

Smiler

Member
Joined:
Posts: 426
#14

I am having an issue at the moment with the sound not always coming on when turning the ignition on. Joying have been quick to answer my messages and have already sent me a firmware update and the factory reset code (which haven't fixed the problem but at least so far they are trying their best).
Sound quality seems impressive.
I'll keep you posted.

Clive603

Member
Joined:
Posts: 654
#15

Great job.
Don't see a major worry if the sound comes on OK if you turn the beast on separately rather than have it come up automatically when switching the ignition on. Or does it have to be set up for automatic turn on so memory settings aren't lost?

Personally I don't like auto start on audio systems. Probably because I don't use radio all the time.

Looks like that will be next months P38 presents.

Clive

Smiler

Member
Joined:
Posts: 426
#16

It has a permanent live feed to keeping memory settings like all units.

Disabling auto-turn-on might be the way this is resolved. It has one-touch activation anyway so it's no great shakes to touch the screen once the engine is running.

They have got back to me again already and have asked me to video what is happening so that they can pass it on to their engineers (along with a photo of the 'system information' screen) so they are certainly trying their best and their English is very good. So far I cannot fault the aftersales service.

I have noticed that (when it is playing) the vocals are very clear. There have been songs that I have been listening to for years that have suddenly made sense when previously the words had got a bit lost.

I shall keep you all up to date as to progress.

Are you sure that you want to perform this action? This action is irreversible.