rangerovers.pub
The only place for a coil spring is up Zebedee's arse
Member
Joined:
Posts: 626

This question is about the Disco, but it's a 4.0 Bosch. I've been adding about a pint of coolant a week, and I don't drive it a lot. It has 165,000km, and as far as I can tell, the HG's have never been done, so I guessed it was time. I removed the heads, and I was hoping to see more definite evidence of bad HG's. I'll try to post photos again. Also, are #6 liner there is a slight brown streak, but liners all look intact, and slightly below flush.
https://imgur.com/ZBEWrOa

Member
Joined:
Posts: 626

enter image description herehttps://imgur.com/ZBEWrOa

Member
Joined:
Posts: 626

I clearly don't know how to properly post photos.

Member
avatar
Joined:
Posts: 7754

No you don't. Display the picture in Imgur, right click on it and select copy link location. Go to write your post, click the insert picture icon and paste the link into the box that pops up.

Slightly out of focus but looks OK to me. Was it pressurising the cooling system or just losing a bit of coolant?

Member
Joined:
Posts: 626

Just losing coolant as far as I know, b

Member
Joined:
Posts: 626

but I didn't really dig into it enough.
I've been trying to post photos

Member
Joined:
Posts: 626

(sorry for my ineptitude) I've been trying to post the photos from my phone. I'll try a computer.

Member
avatar
Joined:
Posts: 7754

Ah yes, Chris No10 spent ages trying to do it on a tablet and failed dismally.

If it wasn't pressurising, spitting all the coolant out and overheating due to a lack of coolant, the liners are fine. Once you've clean the block face up, you should be good to go.

Member
Joined:
Posts: 626

Okay, thanks Richard. Will do.

Member
Joined:
Posts: 626

enter image description here

Member
Joined:
Posts: 626

enter image description here

Member
Joined:
Posts: 591

Are there any marks or grooves around the combustion chambers on the heads? If any of your liners are moving they’ll likely be hitting the head.

Our P38 ran great, didn’t use a drop of oil or water but had a tappet like noise which turned out to be the liner battering the head.

David.

Member
Joined:
Posts: 718

If you are using a pint of coolant a week if it was the HG then you would expect to see the head/valves and piston with that 'steam cleaned' look....
Did you do a pressure check before you took the head off Harv ?

Member
Joined:
Posts: 626

No pressure check. I was quite negligent. I don't think I have the tools to pressure check it, it's probably something I should get? Is there any coolant leak possibility under the front case? There was definitely coolant inside the engine, the valve covers were covered in sludge.

Member
Joined:
Posts: 626

No marks or grooves on the heads, or even the gaskets. I think the liners are intact.

Member
avatar
Joined:
Posts: 7754

If all combustion chambers look like that, there's no coolant getting in there, as Dave says, they'd be steam cleaned and not nicely covered in carbon. Yes, there is a possibility of a leak behind the front cover, both to the inside and also out to the world.

Member
Joined:
Posts: 626

I think I should take apart the front case before putting everything back together. I doubt that I've really wasted my time on HG's, with themilage on the vehicle.

Member
Joined:
Posts: 995

Did you have any coolant on the outside of the engine? Mine was losing coolant and the head gasket was leaking it outwards rather than in to a cylinder.

Mine sprung a leak from the top right corner of the timing cover a couple of years before that too.

Member
Joined:
Posts: 626

No, nothing external, it seems it all ended up in the oil.

Member
Joined:
Posts: 766

But do you have photos of the gaskets themselves - my issue was glaringly obvious when I inspected the gaskets