My long term project is to have the engine in my 2001 Vogue reconditioned/remanufactured. Given all the labour involved & the ease of access to components what other ancillaries should I consider replacing with new or reconditioned items? A few obvious candidates include starter motor, alternator, coils, spark plug leads etc What about oil pump, oil cooler? Anything to do with gearbox or differentials?
I have owned my P38A for eleven years & it's now done 172,500 miles. It had 80K miles when I bought it. It's basically sound if a bit scruffy but has been regularly serviced & is rust free. It cost me £5K & it looks like clean examples are worth at least that now so it's worth it to me to invest some money to keep it running for another twenty years.
If it all works I wonder why GROM don't list their BT3 unit as working with a P38 emulating the CD changer? Their market for Bluetooth add-on units must be diminishing as modern cars have Bluetooth built in. Still at least there is an add-on Bluetooth unit available for the P38. My 2007 Jaguar S-type has built-in Bluetooth for connecting a phone but only for making phone calls & no add-on Bluetooth units are available from GROM or any other company so I have no option except to use a £10 device that plugs into the cigar lighter.
What's the deal with a GROM BT3 unit in a P38? The documents on their website only state support for 2002-2004 Range Rovers with a note that some earlier models may work so to contact them. I emailed them but have had no reply.
I use a £10 gadget that plugs in the cigar lighter, connects by Bluetooth & transmits on a relatively free frequency (108.00 MHz) which is OK but a bit susceptible to interference. I would prefer a proper Bluetooth unit that plugs into the radio. I have a 2001 Vogue with SatNav & CD-changer.
I like the fact that the sunroof gives me a window in the roof but I I don't recall ever having the sunroof open in the eleven years I have owned it. As Richard says what is the point when you have climate control. I don't want the sunroof open for the same reason that I don't have any windows open causing noise & draughts.
I live half the time in France & my 2001 Vogue is French registered. It's a bit tatty but basically sound with just over 170,000 miles on the clock. I'm torn between waiting for the engine to die then fixing it or pre-emptively spending £5K+ on a reconditioned engine.
If you wanted another somewhat similar vehicle I was very impressed with the Freelander 2 that I had as a loaner car when I took my P38 in for a service. The Freelander 2 is basically a Ford made at Halewood. They have a good reputation for reliability & the 2.2L diesel will go on forever. If I was in the market for another car I could go for a Freelander 2.
nigelbb wrote:
You get a good view of the latch by opening the window fully then shining a bright torch down the slot towards the rear then squinting down the slot. I'm pretty sure that if it were some other portion of the latch causing problems that you could operate it with some sort of metal hook or some other amateur locksmith tool. When I was Googling 'P38 driver's door locked' I only found quite extreme suggestions as to how to get the door open eg removing the offside front wing to allow you to unbolt the hinges. I'm surprised that the more subtle approach of squinting down inside the door with the aid of a bright torch didn't get mentioned.
A genuine replacement cable from Land Rover costs over £50 https://parts.jaguarlandroverclassic.com/alr6968-cable-front-door-internal-release.html
Even a Britpart cable is around £30 which is pretty pricey for a 30cm Bowden cable. https://www.lrdirect.com/alr6968-cable-door-release-p38-rh
I don't need the knitting needle any more as I have replaced the sticking cable. Initially I tested the central locking after I had removed the old cable & was disappointed to discover that the bouncing lock problem persisted. It was only when I connected the new cable to the latch & then to the interior handle that I realised that the latch depends on the spring in the interior handle to push the latch back into 'neutral'. The cable that I removed wasn't obviously frayed or kinked & moves quite freely but as it all works smoothly with the new £1/cm cable (I only ran to Britpart not LR) I can only conclude that the old cable was the source of the problem.
I was pleased to note when I had the door card off that it is nice & dry in there with no rust. I was also able to improve the operation of the external handle liberal amounts of WD40 applied while the door card was off.
Knowing that I would probably bugger up some of the plastic fixings that hold the door card I had ordered spares (20 for £2) but only needed to replace two of the "Door Trim Panel Clips" (part number MWC913).
Gilbertd wrote:
So the conclusion is that for Nigel, who's P38 is now on French plates so an LPG conversion isn't viable as to pass the CT, the French MoT, the LPG system needs to be installed using a Government approved installer using a Government approved system for the car (if there even is one for the P38). For his use it might be worth fitting the £800 E85 conversion so the economy on E85 will be back up to, or better than, E10 levels which really will make it cheap to run.
As I understand it E85 just like LPG is less energy dense compared to regular E10 so the amount of fuel that needs to be injected during each cycle is higher so consumption with E85 is always going to be up to 20-30% higher. The fancy flex fuel boxes that retard the ignition vary in price from €200-800 & may enable the engine to run smoothly but cannot improve the fuel consumption to E10 levels. With E85 my Thor runs smoothly without strange smells unmodified with the expected lower fuel consumption so even assuming a box was available for the P38 it wouldn't offer any advantage. Running my P38 on E85 at 89c/L with 14mpg is considerably cheaper than using E10 at €2/L & 17mpg. Cost wise it's the equivalent of getting over 31mpg on E10.
All the ferry companies are OK with LPG conversions. It's only the channel tunnel that won't take them as they aren't licensed to take them. Apparently as LPG wasn't a big thing when they were designing the tunnel they didn't get carrying LPG powered vehicles signed off as safe & now it's too much hassle & expense for them to get it done. Maybe after the P&O debacle they might open to some lobbying. If we travel Dover->Calais we always use the tunnel as it's so much simpler & a little quicker never mind nicer during winter weather. Our place is in Brittany so we always prefer to use Brittany Ferries especially the Portsmouth->Saint-Malo route. It's a 12 hour overnight trip but you get a good night's sleep & then it's under 1.5 hours drive to our cottage whereas if we go via Calais it's a six hour drive.
I too will never use P&O & agree that they will go out of business They have misjudged the outrage their actions have caused & their legal advice must have been poor. A combination of consumer boycott, picketing & the courts will ensure that they don't survive.
Symes wrote:
Well as most of the cost is tax & vat not only gas companies to blame -- pity you can't run bio diesel like my TDI does
My 2001 Vogue runs happily on E85 (85% bioethanol). Fuel consumption is higher at around 14mpg instead of 17mpg on E10 but as in France it currently costs 89.9c/L versus about €2/L for E10 it's still a great saving. I'm sure a large chunk of the price difference is down to lower tax.
You get a good view of the latch by opening the window fully then shining a bright torch down the slot towards the rear then squinting down the slot. I'm pretty sure that if it were some other portion of the latch causing problems that you could operate it with some sort of metal hook or some other amateur locksmith tool. When I was Googling 'P38 driver's door locked' I only found quite extreme suggestions as to how to get the door open eg removing the offside front wing to allow you to unbolt the hinges. I'm surprised that the more subtle approach of squinting down inside the door with the aid of a bright torch didn't get mentioned.
A genuine replacement cable from Land Rover costs over £50 https://parts.jaguarlandroverclassic.com/alr6968-cable-front-door-internal-release.html
Even a Britpart cable is around £30 which is pretty pricey for a 30cm Bowden cable. https://www.lrdirect.com/alr6968-cable-door-release-p38-rh
The drivers door latch has been playing up. It was locked & wouldn't respond to the internal or external handle & the locks 'bounce' when using the fob for central locking. I was getting in the car by the passenger door then clambering across.
It looks like it's the cable from the internal handle that is sticking & preventing the latch from opening. I released the single screw & took the cover round the inner handle off & can see it operates a cable but I couldn't get enough purchase on the cable to operate the lock.
With a torch & one of the wife's knitting needles I was able to release the catch by pressing down on the arm operated by the cable from the interior handle. I put the window down then shone a bright LED torch at the midpoint rearwards & squinting down the slot I could clearly see the end of the cable. Pressing down on the arm at the rear then allowed me to pop the door latch up & open the door.
Unfortunately the lock got stuck again when I re-closed the door but opening the window shining the torch & squinting down the slot again has allowed me to reliably unlock the door. I'm not sure that I'm yet slick enough at the manoeuvre to get in & out of the drivers door at the filling station or shops with just a torch & knitting needle.
I have liberally anointed the latch with WD40 in the hope that whatever has been sticking will be freed up but suspect that it needs the cable replacing. It actually looked clean & rust free but now that I think about it for quite some time I have found both the exterior & interior handles 'sticky' & reluctant to snap back into position when released.
I have been opening the window & using the external handle to open the door & this has been pretty reliable. I only had to resort to the knitting needle a couple of times today
I am so pleased that I didn't have to resort to any of the more extreme methods of getting the door open. I read of people taking the rear door off its hinges to give access to the rear of the striker plate &.even taking off the offside front wing & then undoing the hinges. Not to mention the cold chisel & hammer to smash the lock open.
I am at our place in France at the moment. My 2001 Vogue runs beautifully on E85 (85% bioethanol). Fuel consumption is higher at around 14mpg instead of 17mpg on E10 but as it costs 89.9c/L versus about €2/L for E10 I'm not complaining. E85 was 69.9c/L only a few months ago so there has been a big price rise.
dave3d wrote:
Volvo did a deal, back in the 60's I believe, that when your car had done 1 million miles you could exchange it for a new one.
Long since discontinued I'm afraid.
It looks like this was a one off deal from Volvo for a guy who eventually hit 3,000,000 miles in his 1966 P1800. I'm not sure about a P38 ever hitting that figure. Even Richard has got some way to go before he joins the million mile club.😀
https://wyantgroup.com/remembering-the-three-million-mile-volvo-man/
Gilbertd wrote:
LHD, no sunroof, language set for French and various other odd readings mean the Nanocom and BeCM are not communicating properly and not that the settings have got corrupted. When using the Nano, all systems EXCEPT the BeCM need the ignition on, with the BeCM it needs to be OFF. On an early car the Nano will not connect to the BeCM if the ignition is on but I think with later ones it will but not get proper communications.
Sounds like that might have been my issue as I definitely had the ignition on all the time. I will have to check the values but I won't be changing anything this time.
I nearly forgot. After I had done the bonnet clip, the battery & HEVAC unit I decided to have a play around with the Nanocom I have recently bought. I checked all the systems & was pleased there were no fault codes especially with the new HEVAC. I had a look at the BECM & oddly enough there several things incorrect. Market wasn't set & it said LHD when in fact it's RHD & also said there was no sunroof. There may have been a couple of other items. I made the cardinal error of changing everything at once instead of one at a time. When I tried to write the updates to the BECM the Nanocom rebooted & did this a couple of times then eventually I got the message that the write to the BECM had been performed successfully. Unfortunately when I tried starting the car while I could crank easily enough it wouldn't start. I changed the settings back & updated but it still wouldn't start. I changed the items agin updated & it still wouldn't start. There were no error codes or warning messages. Eventually in desperation I entered the immobilisation code & EKA code then updated once more. Finally it restarted. I was so relieved & learned a valuable lesson - not to fiddle about with stuff I don't understand. I will be reserving use of the Nanocom to reading & clearing faults only when there is a problem.
A number of little jobs. I replaced the little plastic clip that fixes the insulation to the underside of the bonnet & that windscreen washer piping clips to as I discussed in this post https://rangerovers.pub/topic/2827-windscreen-washer-connecter?page=1#pid36847
I replaced the five year old Halfords battery with a Hankook MF31-1000 that I recently bought from www.batterymegastore.co.uk It was a simple swap & only took a couple of minutes to set the windows & sunroof.An annoyance was that I dropped the bolt that fixes the battery stop at the front & it rolled under the battery box. I thought that it would be easy to remove the four bolts & lift up the plastic battery box. Unfortunately the heads of two of the bolts were too rusted to get out with a socket so I shall just have to leave it there & get a new bolt. There was nothing wrong with the old battery but I am working through the car with preventive maintenance to ensure it's as reliable as possible.
I then replaced my HEVAC unit with an identical refurbished one I bought of someone Facebook for £65. They had already done the refurb with the zebra strips to bring the display back to life. I've looked at the webpage that describes how to refurb the unit but it all looked a bit fiddly so when I saw the unit for £65 I snapped it up as they normally sell for at least double that on eBay. My plan is to refurb mine then swap them over again as my original is in better condition. The new unit has a working screen whereas the original had got to be almost unreadable. The new unit has got iffy rockers which stick so generally if you press up it goes all the way to HI & if you press down it goes to LO all soon its own. If you press carefully you can eventually set the temperature correctly
Gilbertd wrote:
Tree clips are the ones that hold the insulation in place but don't have the hook for the washer pipe to clip into. For those you need ALR4425, https://rimmerbros.com/Item--i-ALR4425. You will probably find that the reason it has come out of the clip is that the pipes have shrunk a bit with age so they will no longer reach the clips, mine are dangling on both sides for that reason.
Thanks for the part number. We travel back to France on Sunday so I've order from the very reliable RLD Autos just north west of Paris. The clip is only €1.68 but the postage is €4.99. It's due for delivery next Tuesday. https://www.rld-autos.com/fr/clips-et-fixation/35692-agrafe-tuyau-flexible-discovery-2-et-range-p38-alr4425.html?search_query=ALR4425&results=1
I opened up the bonet today to check oil, coolant, etc & notice that the windscreen washer tubing on the drivers side (RHD) was dangling from the bonnet. Examination revealed that a right angle connection in the tubing should clip onto a plastic stud that secures the insulating blanket under the bonnet. I foolishly tried to lever out the plastic stud with a screwdriver causing top out & disappear somewhere in the engine compartment. I secured the tubing to the insulation with gaffer tape but the insulating blanket is hanging down when the bonnet is open because of the missing stud. This is all a longwinded way of saying does anyone know where I can get a replacement. I looked on Rimmer's website www.lrparts.net but can't find it.
https://ibb.co/LdTVrJm
Morat wrote:
The Duches, being a expensive Bi++.. Lady... has the auto dipping, auto dimming, heated wing mirrors.
The driver's side one has now decided that being reflective was far too common and has changed colour to an unpleasant dog-streak brown.
Not wishing to replace the whole assembly (it's colour coded, too) I looked for a replacement piece of glass.https://www.paddockspares.com/crd101240-rh-mirror-glass-electrochromatic-convex-from-ya430702.html
Holy Carp.
After you have spent £212.99+shipping you aren't even guaranteed an intact mirror
"PLEASE NOTE: None of Paddock Spares' carriers will insure us for glass products. As a result all glass products are sent at the customers risk and no replacements can be sent if damaged. However, we do endeavour to pack everything as well as we possibly can and have VERY FEW breakages."
BTW I'm not sure that they can evade consumer protection legislation in this way.
Symes wrote:
Hi mate so you took the plunge on a P38
I've come to the conclusion that diesel p38s get used and abused more than V8 p48s
They get abused by cheapskates who can't afford to refuel a P38 with a V8 petrol engine. The extreme cheapskates run them on cooking oil.