https://www.ebay.co.uk/itm/175047336705?hash=item28c1a26301:g:NMkAAOSwk1hcZDHe
pfft, doesn't even have the picnic trays!
(oh, and the wrong alloys)
A large box from Island4x4 arrived today with some front air springs. Stand by for pathetic cries for help! But at least I've still got the 1" wood chisel handy :D :D
Folks, I need to reset the front passenger window but it's a bit slow and won't do the full cycle in time.
I'm thinking a quick squirt of lubrication would help - is there any recommended type? Silicon? PTFE? plain ole WD? I'm not sure how much rubber is involved in the door.
It's a pathetic question but I hope you don't mind me asking before I just bugger it up with the wrong stuff :)
Thanks!
Here's the committee hearing. The fun starts at 1hr 27m when the P and O Chief Exec is questioned.
I don't see this having anything to do with Brexit or Johnson - the employment laws haven't changed since we left the EU and the Government have made statements against the PandO redundancy shite. Of course, that doesn't mean they'll do anything - but we'll have to wait and see.
This is naked greed from the management of P and O. May they rot.
Gilbertd wrote:
Not used DFDS for a few years but they used to be very good. As they also do a similar season ticket scheme to that offered by P&O at a similar price but it includes a meal, I'll be giving them a try next time and, unless there's anything I don't particularly like, will be getting a DFDS season ticket. The only downside is that while their crossings are regular, not all are Dover-Calais, some of Dover-Dunkirk. DFDS introduced a couple of new ferries a few years ago which, at the time were the biggest on the route and I used them a few times. Only when P&O introduced their Spirit of Britain and Spirit of France ferries did they loose the biggest on the Channel title. Although considering Spirit of Britain, along with the smaller Pride of Canterbury and Pride of Kent, is tied up in Dover harbour, Pride of Burgundy is tied up in Dunkirk and Spirit of France is halfway through a refit in Rotterdam, none are going anywhere at the moment.
When I checked for yesterday an outbound around 09:00 with the return at 22:00, DFDS wanted £155 while Irish Ferries was £124. The only pandemic restrictions now, assuming fully jabbed and boosted, are that the French want a signed declaration that you don't have any symptoms and haven't knowingly contacted anyone who is positive in the last week and proof of vaccination status. In saying that, I handed my passport and declaration to the French Immigration lady on my way out and she gave me the declaration back and only wanted to see my vac status on my phone from the NHS app. No restrictions at all coming back, not even the dreaded passenger locator form. Can't predict anything on wars or fuel prices though, my crystal ball isn't that good......
Thanks Richard - useful info :)
So, what are DFDS ferries like? I'm pondering a trip via Dover/Calais this summer if the wars stop, pandemics lift and fuel prices fall!
Meanwhile, Tesla 3 estimated delivery: Feb 2023
Ran out of Gas. Had a look at our nearest LPG in stock - 99.9 ppl
Bastards.
and wear wellies!
The new ones have been slathered in WD40 silicon version "Safe on metal, rubber and plastic" so maybe they'll come out easier. Maybe.
They're out! At last.
Turns out that if you get angry enough you don't even need to remove the clips
which is just as well as the ones on the driver's side were not moving for anything.
The wood chisel was a welcome addition to the armoury, thank you Richard. It wasn't quite long enough to get all the top off the spring but it did enough damage for the top clip to no longer hold the plastic in place once I rotated the spring a bit.
I nearly took the drivers side shock out, because I couldn't get any leverage when pulling towards it. I'm confused as to why the clip was put in that way round but if it can go the other way I'll do that on re-assembly. If I bother with clips that is, they're clearly just designed to hold the bags until they rust into place properly.
Now tea :D
I'm guessing option 2 then. I've tried prying the top of the spring (where the clip goes through) and nothing doing. Still, it's a good excuse for a hearty breakfast before re-joining battle :D
The bag with no clips is stuck at the top. I have pry bars (thanks Marty for the suggestion!) - I'm just struggling on where to pry it! It's like trying to lever a blancmange!
The other side isn't giving up the clips. I've only started on the bottom one which is now largely straight but the important bit is still in the hole.
I've packed up for today, I'll get more vicious with it tommorow. I had an optician's appointment in York and on the way back I picked up the male-male hose connector I was missing so now I can jetwash the whole area and get rid of all the crap. I was just using a brush today and there was a lot of mud getting in the way.
The WD40 has been liberally applied for an overnight soak :D
btw, there's an hilarious video on youtube on how to remove rear airbags. It's by an Aussie who pulls the clips out with a bent coathanger wire and the bags pop right out. I'm jealous of places that don't have rust :P
Well, I've undone the air lines and got 2 clips out!
Neither bag will come out, one because it still has one and a half clips holding it in and the other because it just doesn't want to.
This is fun!
Gilbertd wrote:
donmacn wrote:
I turned on the ignition again and the ABS pump ran for about 10/11 secs. After another little bit, turned the ignition on again and it did the same. A problem with the bleeding, or the accumulator?
Might be a problem with the bleeding or it could be internal leakage in the ABS modulator. A car that I worked on seemed fine yet the ABS pump would run for a few seconds every so often with the ignition on. Pulling the reservoir off and found rust particles where it fitted in. Cleaned it out and refilled with fresh fluid and it was fine.
Have I ballsed up the valve block rebuild when I did that a few months ago?
Quite possibly I'm afraid. It sounds like you have a leak on both front valves. The usual cause of internal leaks are the really thin O rings that go around the base of the solenoid plunger tube not seating properly. There is an easy way to check them without taking the valve block out again though. Pull the pipe out that goes to the air spring and lever the collett out. with your tyre pump, fit the tapered thing intended so you can blow up inflatable toys and shove that into one of the holes where the pipe went. Then switch on the pump and watch the gauge. If there are no internal leaks the pressure will rise steadily up to about 80psi (or whatever the pump can manage) then switch off the pump. Keep holding the tapered thing in the hole and see how quickly the pressure drops away. If it is good, it will either not drop at all or will only drop very slowly until you get bored holding the pipe in place. If the pressure only rises slowly and doesn't hold, you've ballsed it up and got an internal leak.
Genius!
Before you pull the trigger on all this, have you done a compression/leakdown test? and one of those "detect exhaust gases in the coolant" tests?
It might just be a valvetrain issue which you could fix without the engine coming all the way out.
You're probably right, and a full rebuild will fix whatever the issue is, but it might just not be necessary. Also, if your compression numbers ARE all out of whack and you have exhaust in the coolant - you'll feel better about dropping lots of money on a rebuild. Or I would, at any rate :)
I've watched the Rimmer Bros video and it all looks feasible for a 12 fingered, shovel handed ape like myself.
As I understand it, I get the EAS up to wading mode (that'll take a while!) and then jack the body up a bit to get stands underneath. I've only got the standard Jack, but four decent stands.
The axle should be... not quite hanging loose? I'm guessing that you can't really have it hanging down all the way or I won't get the springs in.
Thanks in advance!
and you only need it far enough off the bump stops to get you to a garage air line...
Those are the guys.